Skip to main content

An older tautliner can still be a productive part of the fleet, but its restraint hardware needs closer scrutiny than a new build. So, can tracks fit older trailers? Often, yes. The real question is whether the existing body has the structural condition, mounting arrangement and operational suitability to carry a track system safely.

A track retrofit is not a case of drilling a few holes and hanging new restraint equipment. Track location, fastener selection, body-builder advice and the loads being restrained all matter. Get those details right and an older trailer may gain a safer, lower-labour loading arrangement. Get them wrong and the installation can create weak points, damage the body or fail to support the intended restraint task.

Can tracks fit older trailers safely?

Age alone does not rule out a retrofit. Many older curtain-siders and tautliners have sound side structures and can accept new track hardware. Others have corrosion, fatigued rails, previous repairs or unsuitable fixing surfaces that need attention before any restraint equipment is installed.

The determining factor is not the trailer’s build year. It is the condition and design of the area where the track will be fixed. A competent truck body builder or installer should assess the body rather than assume that one track layout suits every trailer.

For fleet operators, this assessment is worth doing before purchasing hardware. It avoids downtime caused by rework and helps ensure the finished arrangement supports the way the vehicle actually carries freight.

Start with the trailer body, not the track

Track hardware transfers restraint forces into the trailer structure. That means the side rail, pillar, chassis-related structure or purpose-designed mounting section must be capable of handling those forces without bending, pulling fasteners through the material or causing local damage.

On an older trailer, inspect for rust around seams and fixing points, cracked welds, loose rivets, distorted posts, damaged or thin side rails, and signs of previous impact repair. Water ingress behind curtains or side panels can also hide corrosion that is not obvious during a quick walk-around.

A straight-looking rail is not automatically a sound rail. The installer needs to know its material, thickness, internal support and how it connects to the body. Aluminium and steel bodies have different fixing considerations, while a repaired section may require a different approach from an untouched section.

If the trailer has been modified over its working life, do not rely on original drawings alone. Added toolboxes, side protection, internal linings, shelving or refrigeration-related equipment can affect access to mounting surfaces and fasteners. The body should be inspected as it stands today.

Check track profile and available mounting space

Not all tracks use the same profile, hole spacing or mounting method. Before specifying a retrofit, measure the available mounting face and confirm there is sufficient clearance for the track, restraint units, curtains and any internal freight protection.

The proposed track position must also work with the loading pattern. A system mounted too high, too low or too close to an obstruction may technically fit the trailer but create unnecessary handling, poor restraint angles or interference with pallets. Drivers need practical access to the equipment without climbing, overreaching or working in an exposed roadside position.

Curtain operation is another consideration. On a curtain-sided vehicle, the track and restraint components must not chafe the curtain, prevent it from tensioning correctly or restrict normal opening and closing. Clearance should be checked through the full operating range, not only with the curtains parked open in the yard.

Fixing methods matter as much as the hardware

The track is only as reliable as its mounting. Fastener type, spacing, backing support and installation torque need to suit the specific trailer body. A fixing method that works well on a new purpose-built rail may not be appropriate for an older thin-wall section or an area affected by corrosion.

Avoid treating the trailer skin as a structural mounting point unless it has been designed and verified for that purpose. Sheet material may hold a component in place, but it may not safely manage the forces generated when freight moves under braking, cornering or an avoidance manoeuvre.

Where access is limited, it can be tempting to use whatever fixing method is quickest. That is a poor trade-off. Installation should be planned around access for inspection, proper fastening and future maintenance. If the correct fixing cannot be achieved in the proposed location, the location or installation design needs to change.

A qualified body builder can determine whether reinforcement, backing plates or an alternative mounting position is required. This is particularly relevant on older trailers where the original structure was not built for the restraint system being considered.

Match the retrofit to the freight task

A track system should be selected around the freight, not simply the vehicle model. A trailer carrying uniform palletised freight on regular metropolitan work has different restraint needs from one carrying mixed industrial loads, long products or changing interstate consignments.

Consider the typical load height, pallet footprint, gaps between freight, weight distribution and how often the load configuration changes. Also consider where the driver loads and unloads. A system that is efficient at a customer dock may not be as practical at regional sites with uneven ground or restricted access.

The full load restraint arrangement needs to support the applicable performance requirements and safe operating practices. Tracks are one part of that arrangement. Freight condition, load placement, blocking, dunnage, restraint devices, anchor points and correct use all contribute to the outcome.

The NHVR Load Restraint Guide 2025 provides useful direction on managing load restraint, but a guide does not turn any individual installation into a compliant solution. Compliance depends on the complete arrangement, the load being carried, correct installation, equipment suitability and the legal requirements that apply to the operation.

Older trailers need a practical inspection plan

Before committing to a retrofit, organise a proper assessment with the body builder or experienced installer. Bring the trailer in clean and unloaded where possible, so the structure and potential mounting areas can be inspected without guesswork.

The assessment should confirm the trailer make and body type, condition of rails and posts, available mounting locations, internal clearance, curtain operation and the freight tasks the vehicle performs. It should also identify any repairs that need to be completed first.

This is a good time to inspect existing restraint equipment. Worn straps, damaged anchor points, bent tracks, missing fasteners and improvised repairs can point to wider maintenance issues. Replacing one component while leaving compromised hardware around it does not improve the overall restraint arrangement.

For fleets, record the agreed track layout, installation details and operating instructions against the trailer number. Consistency helps drivers move between vehicles without having to relearn the restraint process, and it gives workshop teams a clear reference for inspections and replacement parts.

Productivity gains only count when the system is usable

The strongest reason to retrofit a sound older trailer is not appearance. It is improving the way drivers secure freight day after day. A well-planned system can reduce repetitive manual handling, remove unnecessary climbing and help make loading routines more consistent across the fleet.

That benefit depends on driver involvement. Ask the people loading the vehicle where current restraints slow them down, where they are forced to reach, and where loads are most likely to shift or leave gaps. Their feedback often exposes practical issues that a drawing or measurement alone will miss.

StrapNGo’s patented, Australian-made system is designed for tautliners and curtain-sided trucks where safer operation and lower labour are priorities. As with any retrofit, suitability must be confirmed for the individual trailer, its mounting structure and the freight work it performs.

Training remains essential after installation. Drivers should know the intended operating sequence, inspection points, how to identify damage and when to remove equipment from service. A restraint system only delivers its safety and productivity value when it is used correctly on every load.

When a retrofit may not be the right answer

Some trailers are better repaired first, while others may be approaching replacement and not worth modifying. Significant corrosion, repeated structural cracking, major accident damage or a body layout with no suitable mounting zone can make a track retrofit uneconomical or unsuitable.

There are also cases where the issue is not a lack of track. Poor freight planning, unsuitable packaging, inconsistent pallet quality or inadequate load containment may need to be addressed before new hardware will make a meaningful difference.

The sensible approach is to assess the trailer honestly. A lower upfront cost is not a saving if the installation creates future repairs, complicates curtain use or does not suit the loads being carried.

A sound older trailer can often support a modern load restraint upgrade, provided the body structure and installation method are right. Start with an inspection, define the freight task and make the retrofit work for the driver who has to use it every day.

Leave a Reply